We will reply to your message within an hour.
More
Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.
Grade B7, these threaded rods have a tensile strength about one and a half times stronger than low-strength steel rods. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.
About half the strength of medium-strength steel threaded rods, use these for light duty hanging, mounting, and fastening.
18-8 stainless steel threaded rods have good chemical resistance.
More corrosion resistant than 18-8 and 410 stainless steel threaded rods, these 316 stainless steel rods have excellent resistance to chemicals and salt water.
Grade B8M threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.
Made from nylon 6/6, these threaded rods resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.
These acetal threaded rods won't absorb moisture like nylon and fiberglass rods, so they're good for use in wet environments. They resist alcohol, gasoline, and solvents.
One-third the weight of steel, aluminum threaded rods resist corrosion in wet environments.
Brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.
Screw these studs into a tapped hole and use them as a pivot point, hinge, shaft, or locator pin.
These steel studs are zinc plated to resist corrosion in wet environments.
18-8 stainless steel studs have good chemical resistance.
Pass these studs through a hole and weld them in place.
These studs have good chemical resistance. Weld them to stainless steel surfaces.
Weld these studs to uncoated steel surfaces.
316 stainless steel studs have excellent resistance to chemicals and salt water.
Add a stud to thin material when you only have access to one side.
About half the strength of medium-strength steel coupling nuts, these nuts are for light duty fastening applications.
Made from Grade 5 steel, these inch-sized coupling nuts are suitable for most applications.
These coupling nuts have good chemical resistance.
More corrosion resistant than 18-8 stainless steel coupling nuts, these nuts have excellent resistance to chemicals and salt water.
One-third the weight of steel, aluminum coupling nuts resist corrosion in wet environments.
Plastic coupling nuts are chemical resistant, nonconductive, and lightweight.
Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.
Stainless steel coupling nuts have excellent corrosion resistance in most environments.
A smooth rounded body provides a finished look.
Use the sight hole to check for proper thread engagement.
Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench.
Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.
Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.
With the male threaded end on these inserts, mount components directly to plastic parts.
Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.
Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.
Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension. Add right- and left-hand threaded rod ends to build your linkages.
Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.
Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.
Connect these internally threaded shafts directly to threaded components, or use a fastener to secure.
Connect these internally threaded shafts directly to threaded components, or use a fastener to secure. They have a flat surface area that allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.
These stainless steel anchor studs offer excellent corrosion resistance.
A black-oxide finish provides mild corrosion resistance.